Laser-sharp steering, zero slop, corrected geometry for 2.5 and 4.5″ lifts without travel-limiting drop brackets and maximum life from the factory axle ball joint. What more could you ask for? ...
Warning: This product can expose you to chemicals that are known to the State of California to cause cancer. For more information, visit www.P65warnings.ca.gov.
Never has steering stabilization been as important as it is now. The 2005-07 never saw (until now) a “Carli” option to upgrade their factory stabilizer and 2011-16 Super Duty Platform came light on caster – it appeared Ford fixed the problem when they released the 2017 Platform when we saw trucks coming with neutral caster-shims and mid-3° caster specs. Well, somewhere between then and now, the caster spec decreased again. Combine this with the new style track bar that integrates the ball joint into the axle end that can’t seem to make it the duration of an oil change interval without failing all leading to a rise in death wobble claims in nearly brand new trucks.
Minimizing resonation from encountered road obstacles into the front end parts is KEY to combating front end issues like death wobble. We’ve always offered a high mount stabilizer to combat steering wheel feedback in these trucks. The stainless steel design is far superior to the factory unit boasting a custom valve profile improving control of larger aftermarket wheel and tire combinations, offered adjustability to combat right-hand tire pull and is fully rebuildable all while bolting into the factory location ensuring it’s not susceptible to trail damage like many aftermarket stabilizer units are that mount in front of lower steering linkage.
So why the low-mount? 2 Stabilizers is better than one, simply put. This is a general statement – sure, but it applies when looking at OUR product. The high mount braces the Drag link (upper steering linkage bar connecting the passenger side wheel to the pitman arm) close to the pitman arm, itself. The wheels/tires are pretty far from the point of stabilization. Think about it as though you’re trying to control someone’s hand movements by holding their bicep.
With a good enough shock and enough valving, this is doable but adding a second stabilizer to the tie-rod (steering bar connecting Driver and Passenger knuckles) eases the load on the upper stabilizer while providing damping at the mid-point between the two tires further from the steering gear itself. The Low-mount steering stabilizer would actually provide a better feel than the high mount if you’re only going to run ONE stabilizer. Also, this is not limited to lifted/leveled vehicles and can be run on ANY Super Duty with a stock tie-rod.
If both stabilizers are run, one stabilizer per steering bar (Drag link and Tie-rod) means there’s no flop/rocking in the steering, the steering dampers work in every direction (The lower stabilzer dampens left and right, upper stabilizer dampens left/right AND angular load into the gearbox). This optimizes control of larger aftermarket tires while minimizing steering wheel feedback (rocking of the wheel when you encounter a bump). Lastly and perhaps most important for those seeking adjustment, the stabilizers run a true opposing setup; they effectively push against each other. The High mount pushes toward the driver’s side when pressurized and low mount pushes toward the passenger allowing infinite adjustability for whatever radial pull one may encounter.
For you “thru-shaft” stabilizer fans, running BOTH stabilizers eliminates the shaft fluid displacement issue the thru shaft was designed to combat. Running both stabilizers parallel ensures that the fluid displacement when turning thanks to the shaft entering the stabilizer body is offset by the same amount of shaft leaving the body of the other stabilizer. Additionally, with our dual setup, you have the ability to dial in nitrogen pressures to combat tire pull VS. cranking the adjuster on a thru-shaft stabilizer until the pull disappears leaving you with overly tight steering with massive under-steer that won’t return to center.
Our Super Duty High-Mount Steering Stabilizer is a custom Carli Suspension Stainless Steel shock absorber with our own Super Duty steering stabilizer tune. It features a Stainless Steel body,...
Rip corners with surgical precision knowing there’s exactly enough rate to hold the body steady while cutting your line through the dirt. Hit the tarmac and enjoy the benefit of the lighter...
The “UPGRADE” part number does not include the front front differential guard. It’s intended for those already in possession of a Carli Differential Guard with the integrated...
Fox Racing Shox 2.0 Performance Series IFP steering stabilizers help take the load off your steering components and keep your tires tracking straight and true. Oversized off-road tires have a...
This is the newly designed Air Lift WirelessONE on-board air control system. Similar to the wireless model number 25980, this system will allow you to adjust your airbags on the go via a wireless...
Merchant Auto 10123 LBZ Turbo Install Gasket Kit for 2006-2007 GM 6.6L Duramax